Equinox Headband knitting pattern

Disclosure: This post may contain affiliate links and I may make a small commission on items purchased through links in this post at no extra cost to you. You can find out more in my Disclaimer.

Headband overview

The Equinox Headband features a lace motif flanked by two small cables on a reverse stockinette background. The pattern is an 8-row repeat.

The headband is knitted flat and the shorter edges are sewn together forming a twist and hiding the seam. 

This headband is knitted with light weight yarn.

You will find the knitting instructions below.

Size: To fit women’s medium (54-56 cm/ 21 ^3/4 – 22″).

If you are knitting for a smaller/bigger circumference just knit fewer/ more rows.

Gauge: 10 x 10 cm = 21 sts x 28 rows in stockinette stitch after blocking.

Gauge is not crucial for this project.

Finished measurements:

• Width: 12 cm (4.75″) wide.
• Circumference: 50cm (19.75″).

Be sure to check out my other headband knitting patterns.

YOU MIGHT ALSO LIKE:

• Timber Headband knitting pattern
• Mimosa Headband knitting pattern
• Amber Headband knitting pattern
• Roots Headband knitting pattern
• Braided Headband knitting pattern

PIN this for later!

Supplies

To knit this headband you will need the following supplies:

• Yarn: ~50g (1.8oz) light weight yarn (category #3).  I used Drops Lima in the color goldenrod (2923). It’s a blend of  65% wool and 35% alpaca. If you don’t have the mentioned yarn at hand, here are similar yarn options:
  • Rowan Alpaca Soft DK
  • Berroco Ultra Alpaca Light
• Needles: 4mm (US6) knitting needles or size needed to obtain the gauge.
• Tapestry needle
• Scissors

Abbreviations

CO – cast on.

St (s) – stitch (es).

K – knit.

P – purl.

Sl – slip stitch purlwise with yarn in front.

K2tog – knit two stitches together.

Ssk – slip 2 stitches knitwise, put them back on the left needle, knit through back loops together.

Yo – yarn over.

C2B – Slip 1 stitch onto cable needle and leave at back of work. Knit the next stitch, then knit the stitch from the cable needle.

C2F – Slip 1 stitch onto cable needle and leave at front of work. Knit the next stitch, then knit the stitch from the cable needle.

EQUINOX HEADBAND KNITTING PATTERN

Cast on

CO on 31 sts using the Long-tail cast-on method or the one you prefer.

Headband

The first and last 3 stitches form the i-cord edging. You will knit the first 3 stitches of every row, and slip the last 3 stitches of every row.

All the wrong-side rows (2, 4, 6, and 8) are identical.

Row 1: K3, P2, C2B, P2, K3, K2tog, K1, Yo, P1, Yo, K1, Ssk, K3, P2, C2F, P2, Sl3.

Row 2: K5, P2, K2, P6, K1, P6, K2, P2, K2, Sl3.

Row 3: K3, P2, C2B, P2, K2, K2tog, K1, Yo, K1, P1, K1, Yo, K1, Ssk, K2, P2, C2F, P2, Sl3.

Row 4: K5, P2, K2, P6, K1, P6, K2, P2, K2, Sl3.

Row 5: K3, P2, C2B, P2, K1, K2tog, K1, Yo, K2, P1, K2, Yo, K1, Ssk, K1, P2, C2F, P2, Sl3.

Row 6: K5, P2, K2, P6, K1, P6, K2, P2, K2, Sl3.

Row 7: K3, P2, C2B, P2, K2tog, K1, Yo, K3, P1, K3, Yo, K1, Ssk, P2, C2F, P2, Sl3.

Row 8: K5, P2, K2, P6, K1, P6, K2, P2, K2, Sl3.

Repeat rows 1-8 until the headband measures 50cm (19.75″) or your desired length.

Bind off

Bind off sts in pattern (knit over knit stitches, purl over purl stitches).

Step 1: Work 2, bring the first st over the second one.

Step 2: Work the next st, bring the first st over the second one.

Repeat step 2 until you have 1 stitch left, cut the yarn leaving a 30-40cm / 12-16″ tail to seam the headband. Draw the yarn tail through the last stitch and pull it snug.

You will find a detailed tutorial on how to bind off knitting HERE.

Twist

Step 1: With the right side facing you, bring the shorter edges closer together and fold each edge in half so they look like a “V”.

Step 2: Now insert one edge into another. Make sure, that the yarn tail is on the outside, and not in between the layers.

Step 3: Stitch through all 4 layers of knit fabric back and forth.

Finishing

Weave in all loose ends, and turn the headband the right side out.

Wet block the finished item, this process transforms the stitches, makes them look smoother and neater.

Simply soak the knitted item in lukewarm water with some soak wash for 10-15 minutes. Lift it from the water and gently squeeze the excess water out. Next, lay it on a clean towel, and roll it up to remove moisture.

Pin the item to a blocking board or lay it on a clean and dry towel (make sure it doesn’t transfer color) and let it dry. Your knitting will look much better after this.

I hope you enjoyed this headband knitting pattern, be sure to check out my other knitting patterns!

Thank you for stopping by,
Mirella.