Icicle Headband knitting pattern

Disclosure: This post may contain affiliate links and I may make a small commission on items purchased through links in this post at no extra cost to you. You can find out more in my Disclaimer.

Headband overview

The Icicle Headband is a great accessory, that will keep you warm on cold days.

The headband features three cables on a reverse stockinette background with i-cord edges. The pattern is a simple 4-row repeat.

The headband is worked flat and the edges are sewn together.

This is a narrower version of the Green Forest Headband.

You will find the knitting instructions below.

Measurements: To fit women’s medium (54-56 cm/ 21 ^3/4 – 22″).

If you are knitting for a smaller/bigger circumference just knit fewer/ more rows.

Finished size:

• Width: 10cm (4″)
• Circumference: 50cm (19.75″).

Be sure to check out my other headband knitting patterns.

You might also like:

• Green Forest Headband knitting pattern
• Summit Headband knitting pattern
• Thicket Headband knitting pattern
• Roots Headband knitting pattern
• Raindrops Headband knitting pattern

PIN this for later!

Supplies

To knit this headband you will need the following supplies:

• Yarn: ~50g (1.8 oz) medium weight yarn (category #4). I used I used Drops Big Merino in the color ice blue (uni 23). It’s 100% merino wool. If you don’t have the mentioned yarn at hand, here are similar yarn options:

• The One Merino from Wool and the Gang
• Rialto Aran from Debbie Bliss
• Merino Extrafine 85 from Schachenmayr

• 5mm (US 8) knitting needles
• Tapestry needle
• Scissors

Abbreviations

CO – cast on

St (s) – stitch (es)

K – knit

P – purl

Sl wyf – slip stitch purlwise with yarn in front

C4F – slip 2 stitches onto cable needle and leave at front of work. Knit the next 2 stitches, then knit the 2 stitches from the cable needle

HEADBAND KNITTING PATTERN

Cast on

CO on 26 sts using the Long-tail cast-on method or the one you prefer.

Headband

Row 1: K3, *P2, K4* two more times, P2, Sl 3 wyf

Row 2: K3, *K2, P4* two more times, K2, Sl 3 wyf

Row 3: K3, *P2, C4F*, two more times, P2, Sl 3 wyf

Row 4: K3, *K2, P4* two more times, K2, Sl 3 wyf

Repeat rows 1-4 until the headband measures 50cm(19.75″) or your desired length.

Bind off

Bind off sts in pattern (knit over knit stitches, purl over purl stitches).

Step 1: Work 2, bring the first st over the second one.

Step 2: Work the next st, bring the first st over the second one.

Repeat step 2 until you have 1 stitch left, cut the yarn leaving a 30-40cm / 12-16″ tail to seam the headband. Draw the yarn tail through the last stitch and pull it snug.

You will find a detailed tutorial on how to bind off knitting HERE.

Twist

Step 1: With the right side facing you, bring the shorter edges closer together and fold each edge in half so they look like a “V”.

Step 2: Now insert one edge into another. Make sure, that the yarn tail is on the outside, and not in between the layers.

Step 3: Stitch through all 4 layers of knit fabric back and forth.

Finishing

Weave in all loose ends, and turn the headband the right side out.

Wet block the finished item, this process transforms the stitches, makes them look smoother and neater.

Simply soak the knitted item in lukewarm water with some soak wash for 10-15 minutes. Lift it from the water and gently squeeze the excess water out. Next, lay it on a clean towel, and roll it up to remove moisture.

Pin the item to a blocking board or lay it on a clean and dry towel (make sure it doesn’t transfer color) and let it dry. Your knitting will look much better after this.

I hope you enjoyed this headband knitting pattern, be sure to check out my other knitting patterns!

Thank you for stopping by,
Mirella.