Snow Day Hat knitting pattern

Knitted hat
The Snow Day Hat is worked from the bottom up in the round without seams. The folded brim is knit in 2×2 rib, and the body of the hat features a combination of 6-stitch cables and ribbing. 
Total
1
Shares

Disclosure: This post may contain affiliate links, and I may make a small commission on items purchased through links in this post at no extra cost to you. You can find out more in my Disclaimer.


Hat overview

The Snow Day Hat is worked from the bottom up in the round without seams. The folded brim is knit in 2×2 rib, and the body of the hat features a combination of 6-stitch cables and ribbing. 

The hat is knit with medium-weight yarn.

You will find the knitting instructions below. Enjoy!

Be sure to check out my other hat knitting patterns.

Knitted hat

Knitted hat

Gauge: 18stitches x 24rows = 10x10cm (4×4″) in stockinette stitch after blocking on larger needles.

Size:

  • To fit actual head circumference: Adult medium (54-56cm/ 21.25- 22″).
  • Finished height: 22cm/ 8.75″ with the brim folded up 8cm (3.25″).

You might also like:

PIN this for later!

Knitted hat

Supplies

To knit this hat you will need the following supplies:

Abbreviations

C4B dec – slip 2 stitches onto cable needle and leave at back of work. Knit the next  2 stitches together, then ssk the 2 stitches from the cables needle.

C6B – slip 3 stitch onto cable needle and leave at back of work. Knit the next 3 stitches, then knit the 3 stitches from the cable needle.

CO – cast on

K – knit

K2tog – knit two stitches together

M1P – make one purlwise

P – purl

P2tog – purl two stitches together

Ssk – slip 2 stitches knitwise, put them back on the left needle, knit through back loops together

St (s) – stitch (es)

*  * – repeat from * to * until the end of the row or the stated number of times


SNOW DAY HAT KNITTING PATTERN

Cast on

With smaller needles, CO 88 sts using the Long-tail cast-on method or the one you prefer.

Join in the round being careful not to twist the sts (place a marker if you wish to mark the beginning of the round).

I prefer using the invisible join method:

Step 1: CO 88+ 1  extra stitch.

Cast-on for a hat

Step 2: Slip the first st purlwise from the left needle to the right needle.

Step 3: Bring the second st from the right needle over the top of the first st (the one, that we have passed from the left needle)

Step 4: Put that slipped st from the right needle to the left needle: 88sts left. Pull on the strands to tighten.

Turn the knitting so the wrong side of the cast-on is facing you. This way, the neat side of the cast-on will be visible when the brim is folded.

Cast-on for a hat

Brim

Round 1: *P2, K2* to end.

Repeat round 1 until the brim measures 16cm/ 6.25″.

Hat knitting process

Body

Switch to larger needles.

Increase round: *P2, K2, M1P, P1, K6* to end (96sts).

Rounds 1-7: *P2, K2, P2, K6* to end.

Round 8: *P2, K2, P2, C6B* to end.

Repeat rounds 1-8 2  more times. Repeat rounds 1-3 1 more time.

Hat knitting process

Crown

Switch to double-pointed needles or circular needles with a longer cable (for the magic loop method) when necessary.

Round 1: *P2tog, K2, P2tog, K6* to end (80sts).

Round 2: *P1, K2, P1, K6* to end.

Round 3: *P1, K2, P1, K1, Ssk, K2tog, K1* to end (64sts).

Round 4: *P1, K2, P1, K4* to end.

Round 5: *P1, K2, P1, C4B dec* to end (48sts).

Round 6: *P1, K2* to end.

Round 7: *P1, K2tog* to end (32sts).

Round 8: *P1, K1* to end.

Round 9: K2tog to end (16sts).

Hat knitting process

Finishing

Cut the yarn, leaving approximately a 15cm (6″) long tail. Thread a tapestry needle and draw the tail tightly through the remaining stitches. Weave in all loose ends.

Total
1
Shares
A knitted cable beanie.

Fall Sunrise Hat knitting pattern

The Fall Sunrise Hat is worked from the bottom up in the round without seams. The brim is knit in 2x2 rib, and the design features cables. 

Comments1

Leave a Reply

Your email address will not be published. Required fields are marked *

You May Also Like